HI!!
I have a problem.
I bought a Voodoo Lab GCX to change the channels of my head Splawn Superstock.
I saw on the website that is possible with VoodooLab.
I want to use also the mutifx (Digitech GSP1101), and its pedal (Control 2).
The head has two stereo inputs. A Od / Dist / B ONLY clean / OD (or dist)
His pedal has 3 buttons. (Clean / OD - OD / dist - ONLY)
I would be know, what i can do, for tell to the GCX that if I use the GSP's preset 3 , the GCX must call the loop 7 and put on clean the amplifier.
Or if I use the preset 5, I called the loop 7, 6 and 5, so sound od / dist
I would explain what append now.
I select GSP's preset nr3, and the GSP change the preset, but the GCX, don't do nothing. Than a push the FSW 6 or 7 or 8 or 9, and the GSP send it, the CC,84 or 85 or 86 o87 and the GCX set the loop and change the amplifier's channel.
But I want ALL IN ONE.
I want push fsw 1, so select preset1, send to the GCX the MIDI with CC 5 or6 o7 or 8, e this change the amplifier channel.
IT'S POSSIBLE?
I think that I set it all right, but I cann't do what thou wilt. Below I write how I set the parameters, and maybe you can see if I need to change something
The pedal is the Control 2, Digitech GSP1101 dedicated to the pedals.
In midi-setup I get the chance to choose the channel (and I put 16) or the GCX no reply, and that's fine, it's his approach.
-Then I preset in and out, that is if I get a midi command 1, from another device, I choose which preset recall the GSP, and vice versa.
-Then CC / controller map, here I am 16 controller (internal) that I can match a CC, 3 pedals and some external footswitch, and I need for example if I want to change the length of the delay
Then merge-in-that makes me go thru the midi that comes to me from another object in and out directly from gsp to go thru another object
Midi prog-send, it sends a prog change (but the GCX not read them, if sent by something that is not the GCP)
Midi-time tuner
Cc-receve as, and I can choose toggle or no / off (but I do not want to receive them, I want to send)
CC-route to usb (nn I need)
in the settings of Foot controller I
Choice between a 5-setting preset (and 5 stomp box) or 10 presets
-Preset load (ie if I press the preset button 2 times that I do? Recall the original sound or go back to the other before)
-Jump between the desks
-Volume update
- Polarity of the buttons and pedals
MIDI CC / PRG SEND (here's what makes me run the GCX) MIDI CC SEND
I have a series of buttons and pedals and every one can combine a CC to send. I chose the FSW 6,7,8,9 and I've combined the loop 5, 6, 7, 8, and these I will if I press make me change the channels of the head. The only problem is that each of these FSW, it also functions as a pedal, so if I'm on preset 1, clean and hit the FTW7 to attack the delay (un'impost is fixed) gives me this as a channel of tested, on the contrary, if vogli use the same preset, but only to switch from a dist, what do I do? I hit the FSW 8, but in this case I enable or disable the reverb (Set fixed) and for me it is totally inappropriate.
IN ADDITION are on preset 1, Clean, and want to go on the 5 ONLY, I have to press 5 to get the sounds of the solo, but then I'd press FSW 5 (to go from clean to dist) and 8 (to activate only) , and I would tell him I pressed 5, let me go loops 5:08!
-As well as the number of buttons and pedals there is a written INTERNAL DC, and here I put FTW 6 7 8 9 to internal, and I can choose yes or no
-Momentary footswitch, makes me choose how to operate the FSW whether fixed or temporary
-Calibration of expressions
-Name of the banks
Enlighten me, I'm desperate!
