Search found 24 matches

by neuk01642
Tue Jan 23, 2018 10:27 am
Forum: Racks, Switching Systems and MIDI
Topic: Midi CC messages
Replies: 0
Views: 2080

Midi CC messages

Hey all Does anyone know if there are any plans or if it's actually possible to up date the ground control/ GCX to be able to send multiple CC messages with values per patch? I ask because I'm a Helix user and had to buy their floor controller to make full use of the Helix and I came up agains simil...
by neuk01642
Sat Dec 30, 2017 3:06 am
Forum: Racks, Switching Systems and MIDI
Topic: Helix and GCX
Replies: 2
Views: 889

Re: Helix and GCX

No one?
No opinions or thoughts? :cry:
by neuk01642
Fri Dec 29, 2017 3:40 pm
Forum: Racks, Switching Systems and MIDI
Topic: Helix and GCX
Replies: 2
Views: 889

Helix and GCX

Hey all Looking to drive changes on my GCX from my Line 6 Helix. Looking at the GCX manual its littered with warnings about connecting anything other than the Ground Control to the midi in on the GCX as pins 1 and 3 are powered. Does anyone know if the midi out on the Helix has pins 1 and 3 connecte...
by neuk01642
Wed Oct 25, 2017 5:54 am
Forum: Racks, Switching Systems and MIDI
Topic: GCP/GCX/Kemper Power Rack - Pedal weirdness
Replies: 11
Views: 2618

Re: GCP/GCX/Kemper Power Rack - Pedal weirdness

v1.12 should be fine for this so no worries there. As a test, recall any preset that has both expression pedals active. Go into the Preset Edit Mode by pressing and holding the Edit button then use the Select Down button repeatedly to get to the P1 screen. While looking at the P1 screen, rock the p...
by neuk01642
Fri Oct 20, 2017 3:29 am
Forum: Racks, Switching Systems and MIDI
Topic: GCP/GCX/Kemper Power Rack - Pedal weirdness
Replies: 11
Views: 2618

Re: GCP/GCX/Kemper Power Rack - Pedal weirdness

Oh were these units purchased used? If so, did you do a factory restore on the Ground Control Pro so you were at a known starting point before programming? On a Ground Control Pro, the three digit firmware revision number scrolls across the screen when it is first powered up. On a GCX you would loo...
by neuk01642
Thu Oct 05, 2017 8:25 am
Forum: Racks, Switching Systems and MIDI
Topic: GCP/GCX/Kemper Power Rack - Pedal weirdness
Replies: 11
Views: 2618

Re: GCP/GCX/Kemper Power Rack - Pedal weirdness

Odd that the GCX is not responding either... does it's Active LED flash when you press buttons after the freeze occurs? John. When it locks up nothing changes on the GCX, if I remember rightly (because it hasn't done it in a couple of days), the Ground Control LEDs change registering the switch of ...
by neuk01642
Sat Sep 30, 2017 7:20 am
Forum: Racks, Switching Systems and MIDI
Topic: GCP/GCX/Kemper Power Rack - Pedal weirdness
Replies: 11
Views: 2618

Re: GCP/GCX/Kemper Power Rack - Pedal weirdness

Answering questions is what I'm here for, so ask away! OK, so the MIDI connections seem just fine. Interesting that the GCX stops responding also. When this happens is there any activity on the GCX... for instance, does the Active LED flash when this happens? Does the Ground Control Pro still look ...
by neuk01642
Fri Sep 29, 2017 2:05 pm
Forum: Racks, Switching Systems and MIDI
Topic: GCP/GCX/Kemper Power Rack - Pedal weirdness
Replies: 11
Views: 2618

Re: GCP/GCX/Kemper Power Rack - Pedal weirdness

What is your MIDI cable routing? Is anything connected to the Ground Control Pro MIDI In? Hey again John. Bet you love the torrent of noob questions :D So nothing going into the GC midi in. Just the power/miidi into the GC out and into the GCX and the from the last it on the GCX into the in on the ...
by neuk01642
Fri Sep 29, 2017 8:57 am
Forum: Racks, Switching Systems and MIDI
Topic: NOISE, NOISE, NOISE...
Replies: 27
Views: 3827

Re: NOISE, NOISE, NOISE...

Well my budget was swinging wildly from Seymour Duncan Vapour Trail, via Moogerfooger MF delay, through Waza Craft and Jam Delay Llama (which has to be the best name for a pedal ever), to the holy grails of the DMM 1100T or the Chase Bliss Tonal Recall RKM version. But in all honesty I really don't ...
by neuk01642
Fri Sep 29, 2017 8:02 am
Forum: Racks, Switching Systems and MIDI
Topic: NOISE, NOISE, NOISE...
Replies: 27
Views: 3827

Re: NOISE, NOISE, NOISE...

Regarding my pedals.... They are all hand made, with hand etched PCB's. Normally clones of classic pedals. The last one I built was an exact clone of the 18v Colorsound Power Boost, I made 2 one for me and one for a customer. The PCB is a 121 copy of an original, and the pedal performs as per the o...